Idx LC-7S Uživatelský manuál stáhnout pdf

Instruction Manual

How to connect

Slide Slot for

connection

Slide Rail for

connection

：

Lock

：

Release

Product Overview

Important Features

① First connect the AC Cable to the AC Adaptor. Release the main body lock using Open/Close Slide locks to keep the rear cover

open and then connect DC Cable plug to the DC Plug inlet. Set the AC Adaptor to either Built-in or External (refer the previous

section) and close the rear cover, confirm the main body is firmly locked at the Open/Close Slide Locks. Then connect power

plug to the AC Socket.

※When the above condition does not happen even when power is turned on, check that the AC and DC Cables are fully inserted and correctly connected.

② After confirming the AC & DC Cables are correctly connected turn the power on. When the power is ON, the Power LED

lights and the display will show the empty battery mark indicating a battery is not connected.

③ Align the battery in the direction of the charge pins and insert the battery downwards along the slide guides so that the battery

and charger terminals meet and the battery locks firmly in position. When the battery and the LC-7S are correctly connected,

charging starts and the LCD display will show the corresponding charge status.

④ When the charge is complete remove the battery by sliding the battery upwards and in a straight direction along the slide

guides, during this operation be sure to hold both the battery and LC-7S firmly.

Instructions

※

Empty battery mark appears when no battery is connected but the power in on.

4 Channel Simultaneous charging, each channel has an independent charge control.

Each side of the LC-7S is equipped with a slide rail or a slide slot guide to allow multiple chargers to be neatly connected

together to form charging banks. To connect chargers together insert the slide rail of one charger into the slide guide of another

and slide into place keeping both chargers straight at all times. For separation follow the same procedure in reverse.

Be sure chargers are always separated before moving. Any load on the connection parts may cause damage.

7 level charge capacity LCD display panel enables immediate and easy confirmation of charge status.

There are two ways to use the supplied AC Adaptor, External (only the DC Cable is connected inside the charger body) or Built in

(AC Adaptor stored internally within the charger body) .

Specification

General Notes and Safety

Do not attempt to open or modify this unit. All work should be carried out by IDX authorised service personnel only.

Use only with compatible batteries listed in this manual. Charging non-compatible batteries may cause fire, electrical shock or other incidents.

When connecting a battery be sure to insert the battery into the battery socket or connector firmly.

When in use do not place anything on the charger and do not block ventilation holes. Use in a well ventilated area.

Do not expose to, use or place the unit in direct sunlight, extreme dust, water or other hazardous environments.

During charging the temperature of the charger will rise, this is normal and not a malfunction.

A short between the plus (+) and minus (-) charge pins may cause fire, electrical shock or other incidents. Make sure that the charge connector

does not touch any metal parts when a battery is not connected.

Stop charging immediately if the charging does not complete within the designated time. In case of abnormal smell, leak, colour change or

case deformity during use turn the power off and unplug the cable from the socket to avoid possible injury.

Only use the AC Cable and/or Adaptor included with the charger or ones specified. If fused confirm the fuse rating capacity before use.

For continued protection replace any fuses with specified type and rating.

This unit contains no user serviceable parts.

In case of fault or service, please contact your IDX dealer or appropriate IDX office.

①

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

⑫

⑬

⑭

⑮

⑯

⑰

⑱

Below 2.0V

2.0V or above

∼ below 5.73V

5.73V or above

∼ below 7.5V

7.5V or above

∼ below 7.9V

7.9V or above

∼ below 8.1V

8.1V or above

∼ below 8.3V

Preliminary

Charging

Preliminary

Charging

※

rapid flashing

※

normal flashing

Constant Voltage

Charging

Flashing

Solid

Simultaneous 4Ch Charger for 7.2V Battery

(A) How to use the DC Cable when using the external fitting option.

★ The DC Cable can be fed into the charger body from either the right or left side. ★ Store cables by using the hooks at a・b・c and wrapping the cable around.

★ Make sure that DC Plug remains inserted firmly into the connector end.

[

Left

] [

Right

]

[

Left

] [

Right

]

(B) How to secure the DC Cable when using internal storage option.

20060925

Open/Close Slide Lock

Charge Capacity LCD Display Panel

Slide Rail for Charger Interconnection

Slide Slot for Charger Interconnection

Power LED

On/Off Power Switch

Battery Lock Pins

Battery Slide Guides

Battery Charge Terminals

AC Adaptor Lock when externally used

AC Adaptor Lock when internally stored

AC Adaptor Location Hooks

Guide Hooks for DC Cable

DC Input Socket

AC Cable Slot [Left]

AC Cable Slot [Right]

Rear Cover

AC Adaptor & DC Cable

Charger Input DC19V / 60W：

Charge Current

MAX 1550mA

：

Charge Method Pulse Charge → Constant Current/Voltage Charge：

Operating Temperature

0℃∼40℃

：

Dimensions / Weight

(excl power cables)

【

Input

】

AC100V∼240V 50/60Hz ・

【

Output

】

DC19V / 3.16A

：

AC Adapter Input / Output

Voltage Detection Method 7 Level Display

：

LCD Panel Display

NP-F970, NP-F770, NP-F570

：

Compatible Batteries

：

Cooling Fan and Cut Off Function

【

Cooling Fan Operating Condition

】

Cooling fan starts operating automatically when main body internal temperature rises to 50∼55℃ or above.

【

Cooling Fan Stop Condition

】

After fan operates it stops automatically when the main body internal temperature decreases to 45

∼

50℃ or below.

【

Cut Off Function

】

A further safety function will automatically turn the power off when the main body internal temperature rises to

85∼90℃ or above.

※ If the power is turned off by the cut off function, the LC-7S operation does not automatically recover. Disconnect the AC Cable from the AC Socket

and reconnect it after approx. 30 seconds to recover.

CGP-D28S CGA-D54S

120 min 230 min

※

As shown in above (B) illustration, the AC Adaptor can be fitted internally with the AC Cable taken out of either the left

or right AC Cable

input

slots. Note when fitting the AC Adaptor to take the AC Cable out from the chargeris left hand sid e

( [Left] on above (B) illustration,) the AC Adaptor must be inserted in such a way that the DC Cable is at the top otherwise

it will interfere with the fan housing. If it interferes simply turn the AC Adaptor around so that the DC Cable is at the top.

LCD Panel

Display status

Battery

Voltage

8.3V Reached

(

Full charge

)

Constant Current

Charging

Constant Current

Charging

Constant Current

Charging

Complete

: AC Adaptor external lock point(

⑩

). For using the LC-7S in locations that require use of maximum cable length or optimum

positioning of the charger.

(A) External

: AC Adaptor storage lock point(

⑪

). For storing the AC Adaptor and DC Cable internally, organised and space saving.

(

)

Built In

100%

IDX Technology thanks you for choosing the LC-7P and is sure that you will benefit from its unique features. The

LC-7P is a simultaneous 4-Channel charger exclusively for use with Panasonic 7.2V Lithium-ion batteries. Please

note that only designated compatible batteries can be used with the LC-7P. Please utilize this instruction manual

to best maximize and safely use your LC-7P If you have any additional questions, please contact the appropriate

IDX office or visit our website http://www.idx.tv

IDX Technology thanks you for choosing the LC-7S and is sure that you will benefit from its unique features.

The LC-7S is a simultaneous 4-Channel charger exclusively for use with Sony type 7.2V Lithium-ion batteries.

Please note that only designated compatible batteries can be used with the LC-7S. Please utilize this instruction

manual to best mazimize and safely use your LC-7S. If you have any additional questions, please contact the

appropriate IDX office or visit our website http://www.idx.tv

【

AC adapter internally stored

】

Approx. 264（W）×83（H）×138（D）?

〔

10.4（W）×3.3（H）×5.4（D）inches

〕

【

AC adapter externally used

】

Approx. 264（W）× 72（H）×138（D）?

〔

10.4（W）×2.8（H）×5.4（D）inches

〕

Main body weight / approx. 600g

〔

1.3 lbs

〕

《

AC Adapter Dimension : 48（W）×31 （H）×107（D） ?

〔

1.9（W）×1.2（H）×4.2（D）inches

〕

/ Weight：Approx. 230g

〔

0.51 lbs

〕

》

：

:【AC Adaptor internally stored】Approx. 264 (W)×83 (H)×138 (D) mm [10.4(W)×3.3(H)×5.4(D) inches]

【AC Adaptor externally used 】Approx. 264 (W)×72 (H)×138 (D) mm [10.4(W)×2.8(H)×5.4(D) inches]

Main Body Weight / Approx. 600g[1.3 lbs]

AC Adaptor Dimension : 48(W)×31(H)×107(D)mm [1.9(W)×1.2(H)×4.2(D) inches]/ Weight : Approx.230g[0.51 lbs]

：

Charge Time

NP-F970NP-F970

NP-QM91D

NP-F570NP-F570

NP-F770NP-F770

NP-QM71D

, NP-QM91D, NP-QM71D (or equivalent)

Trademarks are the property of their respective owners.

Approx.270min

Approx.180min

Approx.95min

Approx.115min

Approx.165min

20060925 1

Shrnutí obsahu

Strany 1 - 20060925

Instruction ManualHow to connectSlide Slot forconnection Slide Rail forconnection： Lock：ReleaseProduct OverviewImportant Features① First connect the

Komentáře k této Příručce

Žádné komentáře

Idx LC-7S Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Nabíječky Idx LC-7S. IDX LC-7S User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Nabíječky Idx LC-7S